background image

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

DAILY

1. Before use, drain water from the airline filter and compressor.

2. Pour a few drops of Clarke air-line oil, into the tool air inlet. This should be 

carried out regardless of whether or not an in-line mini oiler is used. If an in-
line mini oiler is not used, this procedure should be repeated after every 
two to three hours of use.

3. Keep the body of the tool clean and free from debris.

WEEKLY

• Check the air inlet screen filter 

for blockage and clean if 
necessary.

CLEANING

1. Grit or gum deposits in the tool 

may reduce efficiency and cause 
the tool to run erratically. This 
condition can be corrected by 
cleaning the air strainer and 
flushing out the tool with gum 
solvent or oil.

2. Failing this, the tool should be disassembled, thoroughly cleaned, dried 

and reassembled.

3. The tool may be dismantled by removing the front cover using the hex key 

supplied prior to replacing any worn or damaged parts. You may prefer to 
take the tool to your Clarke dealer if internal maintenance is required.

4. While in a dismantled state, it may be desirable to grease the hammer 

mechanism and applying a small amount of good quality bearing grease.

• This may be better left to your Clarke dealer.

• A hex key is provided for removing the end cover from the wrench.

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE 
AIR SUPPLY BEFORE STARTING ANY CLEANING, OR MAINTENANCE 
PROCEDURES.

Содержание CAT131

















Отзывы: