background image

6

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

9. Abrasive products shall be handled and transported with care. Abrasive 

products shall be stored in such a manner that they are not subjected to 
mechanical damage and harmful environmental influences.

10. DO NOT use separate reducing bushes or adapters to adapt large hole 

abrasive wheels. DO NOT force a stone onto a machine or alter the size of 
the arbor hole.

BENCH GRINDER SAFETY WARNINGS

1. Hold aNY tool or blade being sharpened firmly to prevent loss of control.

2. NEVER install a abrasive flap wheel or sanding disc on this grinder.

3. ALWAYS replace a cracked grinding wheel immediately.

4. NEVER use damaged or incorrect grindstones. The stone and retaining 

fixtures were specially designed for your grinder, for optimum performance 
and safety of operation. Inspect the condition of the grinding stone before 
use and do not use if any damage is found.

5. ALWAYS use the tool rests to steady the workpiece, the torque of the 

spinning grinding wheel may pull the workpiece from your hands.

6. ALWAYS check for damaged parts. Before further use any part that is 

damaged should be carefully checked to determine if it would operate 
properly and perform its intended function. Check for misalignment or 
binding of moving parts, breakage of parts and any other condition that 
may affect the tool's operation. A part that is damaged should be properly 
repaired or replaced at an authorised service center. Following this rule will 
reduce the risk of electric shock, fire or serious injury.

NOTE: 

 Bench grinders used in industrial environments may be subject to 

the The Provision and Use of Work Equipment regulations 1992 
and/or the training requirement of The Abrasive Wheels 
Regulations 1970), or other legislation. If in doubt seek advice

SAFETY SYMBOLS

The meanings of the markings and symbols on the product are shown below

Read this manual 
before use and keep 
in a safe place for 
future reference

Wear eye protection 
when using this tool.

Wear ear protection

Wear dust mask.

Содержание 6502130

























Отзывы: