Clarke 6479509 Скачать руководство пользователя страница 8

Страница: 8 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

BEFORE USE

OIL GAUGE/OIL TOP UP

This machine has an oil chamber built in. The machine can be used for
approximately 20 days without resupplying the lubrication oil, assuming that
the hammer is used continuously for 3-4 hours daily. Check the oil level before
every use.

Check oil level by standing the
machine upright and view the oil
level through the gauge window. If
low;

1. Place hammer on a flat surface

with the oil gauge window facing
upwards.

2. Using the wrench, remove the oil

gauge window cover.

3. Top up the oil well using the oil

bottle supplied. No more than 25ml at a time.

• DO NOT overfill the chamber.

4. Replace the oil gauge window cover and tighten with wrench before

using the hammer again.

POSITIONING THE AUXILIARY HANDLE

The front handle can be positioned
left, right or centre as required.

1. Loosen the handle adjustment

knob by twisting it clockwise.

2. Rotate the handle to the required

position.

3. Secure the handle by twisting the

handle adjustment knob
anticlockwise.

INSERTING A HAMMER BIT / CHISEL

The chuck clamps SDS 30mm Hex hammer bits and chisels without the need
for a chuck key.

Содержание 6479509

















Результаты поиска

Содержание 6479509

Отзывы:

Похожие инструкции для 6479509

Бренды по названию

Популярные бренды

Clarke 6479509, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 6479509

Отзывы:

Похожие инструкции для 6479509

Бренды по названию

Популярные бренды