background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

• Moving to another work area.

• Passing the tool to another person.

13. NEVER use the tool if it is defective or operating abnormally.

14. This tool should be serviced at regular intervals by qualified service 

personnel.

15. Avoid damaging the tool for example by applying excessive force of any 

kind.

16. ALWAYS maintain the tool with care. Keep it clean for the best and safest 

performance.

17. Quick change couplings should not be located at the tool. They add 

weight and could fail due to vibration.

18. DO NOT force or misuse the tool. It will do a better and safer job at the rate 

for which it was designed.

19. DO NOT remove any labels. Damaged labels should be replaced.

20. This tool vibrates with use. Vibration may be harmful to your hands or arms. 

Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek 
medical advice before resuming use.

HAZARDS SPECIFIC TO CUTTING/PUNCHING TOOLS

1. Be careful around all moving parts and pinch points. Always keep your 

fingers away from the point of cutting.

2. Ensure material is properly supported during cutting. Use supports for long 

material. Hold the material securely to prevent it tilting during the cut. Use 
clamps or vices to hold the work piece whenever possible.

3. Take care of sharp edges produced by the work.

4. DO NOT use damaged punches. When replacing cutting tool parts, make 

sure they are correctly and securely fitted.

5. Anticipate the unexpected tool movement due to a binding punch. 

Release the trigger immediately if this occurs.

TRANSPORT & STORAGE

1. DO NOT carry the tool by the air hose.

2. Never carry an air tool with your finger on the trigger.

3. When not in use the air tool must be disconnected from the air supply and 

stored in a dry place out of the reach of children.

Содержание 3110470

















Отзывы: