manualshive.com logo in svg

Clarke 3082110, Инструкция по эксплуатации и техническому обслуживанию, Страница: 3 / 16

Поделиться
Скачать
Clarke 3082110 Скачать руководство пользователя страница 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY RULES 

Before using this equipment it is in your own interest to read and pay attention 
to the following safety rules.

1. Keep the work area clean. Cluttered areas invite injuries. Keep work area 

well lit.

2. Keep children away. Children must never be allowed in the work area.

3. Store idle equipment. When not in use, tools should be locked up in a dry 

location. Always lock up tools and keep out of reach of children.

4. Use eye protection. Always wear approved safety goggles. 

5. Stay alert. Watch what you are doing, use common sense. Do not operate 

any tool when you are tired.

6. Check for damaged parts. Before using any tool, any part that appears 

damaged should be carefully checked to determine that it will operate 
properly and perform its intended function.

7. Do not operate any tool if under the influence of alcohol or drugs. If there is 

any doubt, do not operate the tool.

COMPRESSED AIR EQUIPMENT

1. Compressed air can be dangerous. Ensure that you are thoroughly familiar 

with all precautions relating to the use of compressors and a compressed 
air supply.

2. Never direct a jet of compressed air at people or animals.

3. Always ensure that the equipment being used has a safe working pressure 

exceeding the output pressure of the compressor that it is connected to.

4. Always ensure that the air supply is turned off at the tool outlet and vent all 

compressed air from within the air hose and the equipment attached to it, 
before disconnecting air hoses or other equipment from your compressor.

5. Ensure all fixed airline connections are properly sealed using teflon tape or 

pipe sealant.

6. Never exceed the operating pressure of 43 psi.

PAINT SPRAYING EQUIPMENT

We strongly recommend that paint spraying equipment be used in 
conjunction with appropriate eye and face protecting goggles, glasses or 
spray masks available from most DIY and hardware stores.

1. Always keep the equipment perfectly clean. This will not only prolong its life 

but will also ensure you get the best results. See Maintenance.

Содержание 3082110

















Отзывы:

Нет отзывов