Clarion UNGO PRO SECURITY K20 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 14

background image

9

The learn routine will be exited if:

➤

The ignition is turned on.

➤

The Valet/Program switch is pressed too many times.

➤

More than 15 seconds elapses between programming steps.

One long horn honk (if connected) indicates that the Learn Routine has been exited.

«
...
7
8
9
10
11
...
»

Содержание UNGO PRO SECURITY K20















Отзывы:

Нет отзывов

Похожие инструкции для UNGO PRO SECURITY K20

Predator EVO4+2

Бренд: Falcon Страницы: 11

Бренд: Uniden Страницы: 8

Бренд: Ei Electronics Страницы: 14

Бренд: La Crosse Technology Страницы: 8

Бренд: Geemarc Страницы: 32

Бренд: Geemarc Страницы: 2

Бренд: Draper Страницы: 8

Бренд: Draper Страницы: 8

Civic 08E51-S5D-101

Бренд: Honda Страницы: 24

Бренд: Sentrol Страницы: 8

Бренд: Deltronic Security Страницы: 9

Бренд: SOUNDMASTER Страницы: 61

Бренд: Coopers Страницы: 2

Бренд: Toyota Страницы: 12

Бренд: Connect2Car Страницы: 8

Бренд: Black Widow Security Страницы: 4

Бренд: COP-USA Страницы: 10

Бренд: Home Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды