Clarion ProSecurity SR9000 Скачать руководство пользователя страница 42

Страница: 42 / 60

To exit the learn routine:

The learn routine will be exited if any of the following occurs:

1. Close the open door.

2. Turn the ignition on.

3. There is no activity for longer than 15 seconds.

4. The Valet/Program switch is pressed too many times.

feature menus

The default settings are indicated in

bold

type. Features that have additional settings that can be programmed

using the Prosecurity programmer are indicated with an asterisk (*).

FEATURE NUMBER

ONE-CHIRP SETTING (DEFAULT)

TWO-CHIRP SETTING

1-1

Active arming

Passive arming

1-2

Arm/disarm chirps on

Arm/disarm chirps off

1-3

Ignition lock ON

Ignition lock OFF

1-4

Ignition unlock ON

Ignition unlock OFF

1-5

Active locking only

Passive locking

1-6

Panic with ignition on

No panic with ignition on

1-7

0.8 second door lock pulses

(1)

3.5 (2), 0.4 (3) seconds

1-8

Forced passive arming on

Forced passive arming off

1-9

Automatic engine disable on

Automatic engine disable off

1-10

Armed When Driving (AWD) on

AWD off

1-11

Code Hopping on

Code Hopping off

1-12

Horn Output Pulsed

Constant

1-13

Horn function Full Alarm Only

(1)

Siren function - chirp length
20mS (2)/30mS (3)/40mS (4)/50mS (5)

1-14

Comfort Closure ON

Comfort Closure OFF

NOTE:

The numbers in parentheses indicate the number of times the siren will chirp and the

LED will flash.

menu #1 - basic features

Содержание ProSecurity SR9000

























































Результаты поиска

Содержание ProSecurity SR9000

Отзывы:

Похожие инструкции для ProSecurity SR9000

Бренды по названию

Популярные бренды

Clarion ProSecurity SR9000, Руководство по установке

Результаты поиска

Содержание ProSecurity SR9000

Отзывы:

Похожие инструкции для ProSecurity SR9000

Бренды по названию

Популярные бренды