background image

VRX630

47

English

Installation and Wire

connection manual

1. When the rear of the main unit has been se-

cured with the method shown in Figure 6
unfasten the special screw.

2. Remove the outer escutcheon.

3. Insert the hook plate between the spring and

the universal mounting bracket, fit tab 

B

 of

the spring into hole 

A

 of the hook plate, then

pull the main unit out by the hook plate. (In-
sert both the right and left edges of the hook
plate.) (Figure 9)

Note: Keep the hook plate. You cannot remove the

main unit without disengaging the hook plate.

 

6.

REMOVING THE MAIN UNIT

1. Be sure to turn the power off before wiring.

2. Be particularly careful where you route the

wires.

Keep them well away from the engine, and
exhaust pipe, etc. Heat may damage the
wires.

3. If the fuse should blow, check to see if the

wiring is correct.

If it is, replace the fuse with a new one with
the same amperage rating as the original.

4. When any fuse is to be replaced, pull out the

fuse (15A) at the rear of the main unit and
put in a new one (Fig.10).

 

7.

CAUTIONS ON WIRING

5.

When connecting the ground lead, fasten the
ground lead (black) securely to a clean metal
plate on the car. (Figure 11)

If the set is insufficiently grounded, it may not
operate or there may be noise.

After the connection, fix the lead by a clamp
or insulation tape for protection.

CAUTION

Figure 11

Figure 10

Содержание pro audio vrx 630











Отзывы: