City Theatrical 5792 SHoW DMX Neo Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 40

background image

3

About this Manual

Section 4 provides the specifications, notifications and regulations necessary for safe and
effective operation of the SHoW DMX Neo Radio.

This manual divides the two operating modes into separate sections: Neo operation mode
implementation and Classic operation mode implementation. It is not recommended to
implement the latter.

Section 5 describes implementing Neo mode. The section is broken into two sub sections, one
for the 5792 (SHoW DMX Neo Radio for OEM) and one for 5794 (SHoW DMX Neo Radio for W-
DMX). Neo mode implementations are the preferred method of integration.

Section 5.1.2 gives examples of common implementations. It is suggested to follow one of
these examples.

Section 6 was intended to describe the implementation of Classic mode. However, CTI strongly
recommends its customers avoid implementing Classic mode and thus has excluded section 6
from this manual. If compatibility to older SHoW DMX products is required, Classic mode must
be implemented as an addition to Neo mode. If you are interested in pursuing such
functionality, please contact City Theatrical at (201)-549-1160.

Section 7 describes the protocol and command set for the configuration mode.

«
...
5
6
7
8
9
...
»

Содержание 5792 SHoW DMX Neo









































Отзывы:

Нет отзывов

Похожие инструкции для 5792 SHoW DMX Neo

Бренд: Jafar Страницы: 9

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Бренд: PUTCO Страницы: 2

Бренд: Apricus Страницы: 32

Бренд: Belimo Страницы: 2

Бренд: Watts Страницы: 12

Бренд: olympia electronics Страницы: 22

Бренд: Madas Страницы: 10

TRULUX DMX 3Z Touch Control

Бренд: American Lighting Страницы: 2

Бренд: Lucci comfort Страницы: 3

Бренд: GSD Страницы: 2

Бренд: Infineon Страницы: 13

Бренд: TJERNLUND Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды