Citizen BD2-1220 Скачать руководство пользователя страница 71

Страница: 71 / 100

— 69 —

(2) If a sufficient area cannot be provided as a result of step

(1), the print area is extended toward the left (So, the left
margin is decreased).

(3) If a sufficient area cannot be provided as a result of step

(2), the right spacing is trimmed.

• When mapping a bit image (Or downloaded bit image), if the

print area is narrower than the minimum width of the bit image
(Two dots for single density, or one dot for double density),
only the line for that image is handled as follows:

(1) The print area is extended toward the left (So, the left

margin is decreased) until it is equal to the minimum width
of the image, but not wider than the printable area.

[Default]

nL=64, nH=2 (When 58mm wide paper is used: nL=176, nH=1)

Since the default value varies depending on the number of
columns, refer to “Defing the print area in PAGE MODE; ESC
W”, for more information.

[See Also]

GS L, GS P

(1)

Extended
toward
the right

Printable Area

Left Margin

(2) The left margin

is trimmed

Print Area Width

Содержание BD2-1220





































































































Результаты поиска

Содержание BD2-1220

Отзывы:

Похожие инструкции для BD2-1220

Бренды по названию

Популярные бренды

Citizen BD2-1220, Справочник по командам

Результаты поиска

Содержание BD2-1220

Отзывы:

Похожие инструкции для BD2-1220

Бренды по названию

Популярные бренды