Cisco WCM300 - Channel Bonded Cable Modem Скачать руководство пользователя страница 61

Страница: 61 / 88

C H A P T E R

5-1

Cisco Cable Wideband Solution Design and Implementation Guide, Release 1.0

OL-10705-02

Monitoring and Troubleshooting Wideband
Components

This chapter provides an introduction to monitoring and troubleshooting the wideband components of
the Cisco Cable Wideband Solution, Release 1.0. The chapter includes the following topics:

•

Monitoring Wideband Components, page 5-1

•

Troubleshooting Wideband Components, page 5-13

Monitoring Wideband Components

The Cisco IOS command-line interface includes commands that can be issued on the CMTS for the
following:

•

Monitoring Wideband SIPs, page 5-2

•

Monitoring Wideband SPAs, page 5-3

•

Monitoring Wideband Channels, page 5-6

•

Monitoring RF Channels, page 5-10

•

Monitoring Wideband Cable Modems, page 5-10

For detailed information on the syntax, usage, and additional examples for each command, see the
documents shown in

Table 5-1

Note

Many of the commands used to configure the Cisco uBR10012 router and the Cisco Wideband SIP and
SPA

are not

currently part of the command set that can be searched with the Cisco Command Lookup

Tool (available on Cisco.com). Use the documents listed in

Table 5-1

to find information on these

commands.

Table 5-1

Wideband Command Reference Documentation

Document Command

Described

Cisco uBR10012 Universal Broadband Router
SIP and SPA Software Configuration Guide

Commands for the Wideband SIP and Wideband
SPA, including commands for RF and wideband
channels

Содержание WCM300 - Channel Bonded Cable Modem

























































































Результаты поиска

Содержание WCM300 - Channel Bonded Cable Modem

Отзывы:

Похожие инструкции для WCM300 - Channel Bonded Cable Modem

Бренды по названию

Популярные бренды

Cisco WCM300 - Channel Bonded Cable Modem, Руководство по внедрению

Результаты поиска

Содержание WCM300 - Channel Bonded Cable Modem

Отзывы:

Похожие инструкции для WCM300 - Channel Bonded Cable Modem

Бренды по названию

Популярные бренды