Cisco WCM300 - Channel Bonded Cable Modem Скачать руководство пользователя страница 38

Страница: 38 / 88

2-22

Cisco Cable Wideband Solution Design and Implementation Guide, Release 1.0

OL-10705-02

Chapter 2 Cisco Cable Wideband Components

Where to Find Information on Solution Hardware Components

Table 2-7

Cisco Hardware Components: Where to Find More Information

Solution Component

Where to Find More Information

uBR10012 chassis

Performance Routing Engine 2 (PRE2)

Timing, Communication, and Control Plus card (TCC+)

DC Power Entry Modules (DC PEMs)
AC Power Entry Modules (AC PEMs)

Fan assembly module

LCD module

Regulatory Compliance and Safety Information for the Cisco
uBR10012 Universal Broadband Router

Cisco uBR10012 Universal Broadband Router Hardware
Installation Guide

(full installation guide)

Cisco uBR10012 Universal Broadband Router Hardware
Installation Guide

(quick start guide)

uBR10-MC5X20S/U/H and uBR10-MC5X20U-D
cable interface line cards

Cisco uBR10012 Universal Broadband Router Hardware
Installation Guide

(full installation guide)

Cisco uBR10-MC5X20S/U/H Cable Interface Line Cards -
Hardware Installation Guide

Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card
with Universal Cable Holder—UCH1

Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card
with Universal Cable Holder—UCH2

Half-Height Gigabit Ethernet (HHGE) network uplink
line card

Cisco uBR10012 Universal Broadband Router Hardware
Installation Guide

(full installation guide)

Cisco uBR10012 Universal Broadband Router Gigabit Ethernet
Half-Height Line Card Installation

Wideband SPA Interface Processor (SIP)

Wideband Shared Port Adapter (SPA)

Cisco uBR10012 Universal Broadband Router SIP and SPA
Hardware Installation Guide

Cisco uBR10012 Universal Broadband Router SIP and SPA
Software Configuration Guide

Harmonic NSG 9116 and NSG 9000 edge QAM devices Refer to the vendor documentation.

Scientific Atlanta Continuum DVP XDQA24 edge
QAM device

Refer to the vendor documentation.

Vecima Networks VistaLynx VL1000 edge QAM
device

Refer to the vendor documentation.

Linksys WCM300-NA, WCM300-EURO, and
WCM300-JP wideband cable modems

Release Notes for Linksys WCM300 Cable Modem Software

Cisco Cable Wideband Solution Design and Implementation Guide,
Release 1.0 (this document)

Cisco uBR10012 Universal Broadband Router SIP and SPA
Software Configuration Guide

Scientific Atlanta DPC2505 and EPC2505 wideband
cable modems

Refer to the vendor documentation.

Содержание WCM300 - Channel Bonded Cable Modem

























































































Результаты поиска

Содержание WCM300 - Channel Bonded Cable Modem

Отзывы:

Похожие инструкции для WCM300 - Channel Bonded Cable Modem

Бренды по названию

Популярные бренды

Cisco WCM300 - Channel Bonded Cable Modem, Руководство по внедрению

Результаты поиска

Содержание WCM300 - Channel Bonded Cable Modem

Отзывы:

Похожие инструкции для WCM300 - Channel Bonded Cable Modem

Бренды по названию

Популярные бренды