Cisco VG310 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 96

background image

If the

rommon 1>

prompt is displayed, your system has booted in ROMmon mode. For information on

the ROMmon, see the section on using the ROMmon in the

Cisco VG350, Cisco VG310 and Cisco 320

Voice Gateway Software Administration and Configuration Guide

at Cisco.com.

Performing the Initial Configuration on the Voice Gateway

Use the following tools to perform the initial configuration on the voice gateway:

•

Using the setup Command Facility, on page 55

•

Using Cisco Configuration Professional Express, on page 58

•

Using Cisco IOS CLI

—

Manual Configuration, on page 58

Using the setup Command Facility

Before You Begin

The

setup

command facility prompts you to enter the information that is needed to configure Cisco VG310

or Cisco VG320 quickly. The facility steps you through a initial configuration, including LAN and WAN
interfaces. For more general information about the

4719407618

command facility, see the chapter

Configuration

Using Setup and Autoinstall in the Cisco IOS Configuration Fundamentals Configuration Guide, Release
12.4

, at

Configuration Fundamentals Configuration Guide, Cisco IOS Release 15.0S

.

This section explains how to configure a hostname for the voice gateway, set passwords, and configure an
interface for communication with the management network.

If you make a mistake while using the

setup

command facility, you can exit and run the

setup

command

facility again. Press

Ctrl-C

, and enter the

setup

command in privileged EXEC mode (

Router#

).

Note

Procedure

Step 1

From the Cisco IOS CLI, enter the

setup

command in privileged EXEC mode:

Router>

enable

Password: <

password

>

Router#

setup

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]:

You are now in the Setup Configuration Utility.

Step 2

To proceed using the setup command facility, enter

yes

.

The following message is displayed:

Continue with configuration dialog? [yes/no]:

At any point you may enter a question mark '?' for help.

Cisco VG310 and Cisco VG320 Voice Gateways Hardware Installation Guide

OL-31292-01

55

Configuring the Cisco VG310 and Cisco VG320 Voice Gateways

Performing the Initial Configuration on the Voice Gateway

«
...
65
66
67
68
69
...
»

Содержание VG310

































































































Отзывы:

Нет отзывов

Похожие инструкции для VG310

Бренд: ABB Страницы: 44

Бренд: H3C Страницы: 29

EKI-1200-CE Series

Бренд: Advantech Страницы: 67

FieldServer ProtoNode

Бренд: SMC Sierra Monitor Страницы: 4

ServiceRouter V3

Бренд: Eurogard Страницы: 4

Бренд: Gree Страницы: 21

Бренд: Nortel Страницы: 134

Remote Office 9150

Бренд: Nortel Страницы: 570

Envoy Communications Gateway

Бренд: enphase Страницы: 100

UNIGATE EL-DeviceNet

Бренд: DEUTSCHMANN AUTOMATION Страницы: 62

UNIGATE CM - PROFIBUS

Бренд: DEUTSCHMANN AUTOMATION Страницы: 62

Бренд: Ness Страницы: 4

Бренд: ZyXEL Communications Страницы: 361

Бренд: ViewSonic Страницы: 53

Бренд: Avaya Страницы: 254

Бренд: OATI Страницы: 10

Бренд: Avaya Страницы: 494

Бренд: Tainet Страницы: 225

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды