Cisco Versatile Interface Processor (VIP6-80) (VIP6-80) Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

background image

10

Versatile Interface Processor (VIP6-80) Installation and Configuration Guide

OL-5078-01

Traffic Management

The VIP6-80 supports the following:

•

Simple Network Management Protocol (SNMP) agent V1 (RFCs 1155–1157)

•

Management Information Base (MIB) II (RFC 1213)

Installation Prerequisites

This section provides installation prerequisites to ensure a successful VIP6-80 installation, and includes
the following sections:

•

Software Requirements, page 10

•

Hardware Requirements, page 10

•

Microcode Requirements, page 11

•

Tools and Parts Required, page 11

•

Agency Approvals, page 11

•

Safety Guidelines, page 11

Software Requirements

The minimum Cisco IOS Release requirements for VIP6-80 are listed in

Table 6

. For configuration

information and support, refer to the modular configuration and modular command reference
publications in the Cisco IOS software configuration documentation set that corresponds to the software
release installed on your Cisco hardware.

Note

You can access Cisco IOS software configuration and hardware installation and maintenance
documentation on the World Wide Web at

http://www.cisco.com

. Translated documentation is available

at the following URL: http://www.cisco.com/public/countries_languages.shtml.

Hardware Requirements

The VIP6-80 is a single motherboard. It operates with the following:

•

Cisco 7505, Cisco 7507, Cisco 7507-MX, Cisco 7513, Cisco 7513-MX, and the Cisco 7576 routers
with the Route Switch Processor (RSP1, RSP2, RSP4, RSP4+, RSP8, or RSP16); the RSP should
have at least 64 MB of DRAM

Table 6

VIP6-80 Minimum Software Release Requirements

VIP Release

Minimum Cisco IOS Supported Releases

VIP6-80

Cisco IOS Release 12.0(22)S or later release of Cisco IOS Release 12.0 S
Cisco IOS Release 12.1(12)E or later release of Cisco IOS Release 12.1 E
Cisco IOS Release 12.2(12)T or later release of Cisco IOS Release 12.2 T

«
...
8
9
10
11
12
...
»

Содержание Versatile Interface Processor (VIP6-80) (VIP6-80)









































Отзывы:

Нет отзывов

Похожие инструкции для Versatile Interface Processor (VIP6-80) (VIP6-80)

Mini Field Agent

Бренд: GE Страницы: 87

OfficeConnect 1600

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

Бренд: YASKAWA Страницы: 34

Бренд: QNAP Страницы: 20

VigorIPPBX 2820 Series

Бренд: Draytek Страницы: 29

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

Бренд: DPtech Страницы: 39

Бренд: KPN Страницы: 14

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: Isee Страницы: 68

Бренд: Compro Technology Страницы: 2

Бренд: Korenix Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды