Cisco RSP8 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 92

Cisco RSP8 Скачать руководство пользователя страница 85

85

Route Switch Processor (RSP8) Installation and Configuration Guide

OL-4920-02

Reference Information

If you set the boot field value to 0x2 through 0xF and there is a valid boot system command stored in
the configuration file, then the router boots the system software as directed by that value. If there is no
boot system command, the router forms a default boot filename for booting from a network server. (See

Table 11

for the format of these default filenames.)

In the following example, the software configuration register is set to boot the router from onboard Flash
memory and to ignore the Break function at the next reboot of the router:

Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)# config-register 0x102

Router(config)# boot system flash

[filename]

Router(config)# end

Router#

The server creates a default boot filename as part of the automatic configuration processes. To form the
boot filename, the server starts with the name cisco and adds the octal equivalent of the boot field
number, a hyphen, and the processor-type name.

Table 11

lists the default boot filenames or actions for the processor.

Note

A boot system configuration command in the router configuration in NVRAM overrides the default
netboot filename.

Table 11

Default Boot Filenames

Action/Filename

Bit 3

Bit 2

Bit 1

Bit 0

Bootstrap mode

0

0

0

0

Default software

0

0

0

1

cisco2-RSP

0

0

1

0

cisco3-RSP

0

0

1

1

cisco4-RSP

0

1

0

0

cisco5-RSP

0

1

0

1

cisco6-RSP

0

1

1

0

cisco7-RSP

0

1

1

1

cisco10-RSP

1

0

0

0

cisco11-RSP

1

0

0

1

cisco12-RSP

1

0

1

0

cisco13-RSP

1

0

1

1

cisco14-RSP

1

1

0

0

cisco15-RSP

1

1

0

1

cisco16-RSP

1

1

1

0

cisco17-RSP

1

1

1

1

«
...
83
84
85
86
87
...
»

Содержание RSP8





























































































Отзывы:

Нет отзывов