manualshive.com logo in svg

Cisco PA-VXA Series, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-VXA Series Скачать руководство пользователя страница 9

 

ix

T1/E1 Digital Voice Port Adapter Installation and Configuration

OL-3592-02

Preface

Obtaining Documentation

•

Cisco 7301 routers:

For hardware installation and maintenance information, refer to the Cisco 7301 Installation and 
Configuration Guide or the Cisco 7301 Router Quick Start Guide.

•

Cisco 7401ASR routers:

For hardware installation and maintenance information, refer to the Cisco 7401ASR Installation and 
Configuration Guide or the Cisco 7401ASR Quick Start Guide.

•

Cisco 7500 series routers:

For hardware installation and maintenance information, refer to the following publications:

–

Cisco 7500 Installation and Configuration or the quick start guide that shipped with your router

–

Second-Generation Versatile Interface Processor (VIP2) Installation and Configuration 

–

Fourth-Generation Versatile Interface Processor (VIP4) Installation and Configuration

–

Versatile Interface Processor (VIP6-80) Installation and Configuration

•

For international agency compliance, safety, and statutory information for WAN interfaces:

–

Site Preparation and Safety Guide

–

Regulatory Compliance and Safety Information for the Cisco 7200 Series Routers

–

Cisco 7300 Series Internet Routers Regulatory Compliance and Safety Information

–

Cisco 7401ASR Regulatory Compliance and Safety Information

–

Regulatory Compliance and Safety Information for the Cisco 7500 Series Routers

•

To view Cisco documentation or obtain general information about the documentation, refer to the 
following sources:

–

“Obtaining Documentation” section on page ix

.

–

“Obtaining Technical Assistance” section on page xi

.

–

Customer service at 800 553-6387 or 408 526-7208. Customer service hours are 5:00 a.m. to 
6:00 p.m. Pacific time, Monday through Friday (excluding Cisco-observed holidays).

–

Cisco Information Packet that shipped with your router or switch.

Obtaining Documentation

Cisco provides several ways to obtain documentation, technical assistance, and other technical 
resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation on the World Wide Web at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

International Cisco web sites can be accessed from this URL:

http://www.cisco.com/public/countries_languages.shtml

Содержание PA-VXA Series

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды