manualshive.com logo in svg

Cisco PA-VXA Series, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-VXA Series Скачать руководство пользователя страница 55

 

4-5

T1/E1 Digital Voice Port Adapter Installation and Configuration

OL-3592-02

Chapter 4      Configuring the PA-VXA, PA-VXB, and PA-VXC

Configuring the Interface

Step 4

Use the controller command in configuration mode to enter the controller configuration mode for the 
desired controller:

Router(config)# controller t1 

Router(config-controller)#

Note

The following steps must be done in controller configuration mode.

Step 5

Use the framing command to select carrier framing. If the card is set to T1, set framing to extended super 
frame (ESF) as shown in the example below:

Router(config-controller)# framing esf

If the card is set to E1, set framing to CRC4 as shown in the example below:

Router(config-controller)# framing crc4

Step 6

Use the linecode command to select the line coding. T1 cards should be set to binary 8-zero substitution 
(B8ZS) as shown in the example below:

Router(config-controller)# linecode b8zs

E1 cards should be set to HBD3 line code as shown in the example below:

Router(config-controller)# linecode hbd3

Step 7

Use the clock source command to select between internal or line clocking. 

Router(config-controller)# clock source line

Note

Line clocking is normally selected because of the highly accurate clock source supplied by 
the network.

Step 8

When installed in a Cisco 7200 VXR router, use the frame-clock-select priority carrier-type controller 
command in configuration mode to specify the clock source. This command may be used to specify 
backup clock sources, as shown in the example below:

Router(config)# frame-clock-select 1 T1 1/0

Router(config)# frame-clock-select 2 T1 1/1

The example above assigns T1 1/0 as the primary clock source. If that clock fails, T1 1/1 will become 
the primary clock source.

Step 9

Use the ds0-group number timeslots range type command to create a DS0 group. 

Router(config-controller)# ds0-group 1 timeslots 10-18 type e&m-wink-start

Note

The time slot range for a T1 card is 1 to 24, the time slot range for an E1 card is 1 to 30.

Step 10

Change the shutdown state to up and enable the interface: 

Router(config-controller)# no shutdown

Содержание PA-VXA Series

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды