manualshive.com logo in svg

Cisco PA-MC-2T3-EC=, Руководство по установке и настройке, Страница: 17 / 96

Поделиться
Скачать
Cisco PA-MC-2T3-EC= Скачать руководство пользователя страница 17

1-7

PA-MC-T3-EC Port Adapter Installation and Configuration

OL-10589-02

Chapter 1      Overview

  Identifying Interface Addresses

Table 1-2

 explains how to identify interface addresses

. 

In Cisco 7200 VXR routers, port adapter slots are numbered from the lower left to the upper right, 
beginning with port adapter slot 1 and continuing through port adapter slot 2 for the Cisco 7202, slot 4 
for the Cisco 7204 and Cisco 7204VXR, and slot 6 for the Cisco 7206 and Cisco 7206VXR. (Port 
adapter slot 0 is reserved for the optional Fast Ethernet port on the I/O controller—if present.) 

The interface addresses of the interfaces on the

 

PA-MC-T3-EC in port adapter slot 1 are 1/0 and 1/1 (port 

adapter slot 1 and interfaces 0 and 1). If the

 

PA-MC-T3-EC was in port adapter slot 4, these same 

interfaces would be numbered 4/0 and 4/1 (port adapter slot 4 and interfaces 0 and 1). 

Table 1-2

Identifying Interface Addresses 

Platform

Interface Address Format

Numbers

Syntax

Cisco 7200 VXR routers

Port-adapter-slot-number/interface-port-number

Port adapter slot—0 through 
6 (depends on the number of 
slots in the router)

1

Interface port—0 and 1

1.

Port adapter slot 0 is reserved for the Fast Ethernet port on the I/O controller (if present).

1/0

Port Adapter Jacket Card 
with the Cisco 7200 VXR 
routers

2

2.

Port adapter slot 0 can accept the Port Adapter Jacket Card if an NPE-G1 or NPE-G2 is installed.

Port-adapter-slot-number/interface-port-number

Port adapter slot—0 through 
7 (depends on the number of 
slots in the router)

3

Interface port—0 and 1

3.

Port adapter slot 0 is reserved for the Fast Ethernet port on the I/O controller (if present).

1/0

Cisco 7201 router

Port-adapter-slot-number/interface-port-number

Port adapter slot—always 1

Interface port—0 or 1

1/0

Cisco 7301 routers

Port-adapter-slot-number/interface-port-number

Port adapter slot—always 1

Interface port—0 or 1

1/0

Содержание PA-MC-2T3-EC=

































































































Отзывы:

Нет отзывов