Cisco PA-MC-2T3-EC= Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 96

Cisco PA-MC-2T3-EC= Скачать руководство пользователя страница 14

1-4

PA-MC-T3-EC Port Adapter Installation and Configuration

OL-10589-02

Chapter 1 Overview

LEDs

LEDs

The PA-MC-T3-EC has three status LEDs located on its faceplate: one ENABLED LED, and an A/L
(active/loopback) LED, and C/A (carrier/alarm) LED for each port.

Figure 1-3

PA-MC-2T3-EC Status LEDs—Partial Horizontal View

In addition to the interface status information provided by the LEDs, you can also retrieve detailed
interface status information either through the router console port or through Telnet or Simple Network
Management Protocol (SNMP).

Port Adapter Slot Locations

This section discusses port adapter slot locations on the Cisco 7200 VXR routers.

Figure 1-4

shows a Cisco 7206VXR with port adapters installed. This illustration also shows the Port

Adapter Jacket Card installed in the I/O controller slot. The Cisco 7204VXR router is not shown;
however, the PA-MC-T3-EC can be installed in any available port adapter slot (1 through 5).

In the Cisco 7206VXR as a router shelf in a Cisco AS5800 Universal Access Server, port adapter slot 1
is in the lower left position, and port adapter slot 6 is in the upper right position.

LED Label

Color

State

Meaning

ENABLED

Green

On

After system initialization, the port is enabled for
operation.

—

Off

The port is not enabled for operation.

A/L (active/loopback)

Green

On

Port is enabled, loopback is off.

Amber

On

Port is enabled, loopback is on.

—

Off

Port is not enabled

C/A (carrier/alarm)

Green

On

Port is enabled, valid signal without alarms.

Amber

On

Port is enabled, valid signal with alarms.

—

Off

Port is not enabled.

158049

ENABLED C/A

A/L

C/A

A/L

PA-MC-2T3-EC

TX

RX

«
...
12
13
14
15
16
...
»

Содержание PA-MC-2T3-EC=

































































































Отзывы:

Нет отзывов