Cisco PA-4C-E Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 40

background image

36

PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration

OL-3743-02

Configuring the HP ESCON PA

Step 5

To verify that the correct microcode is loaded according to the new instructions, enter the
show controllers EXEC command. The display indicates the currently loaded and running microcode
version for each HP ESCON PA.

Step 6

To verify the contents of the configuration file, enter the show running-config EXEC command. You
can also verify that the correct software image is configured to load at system restart or reload by using
the show startup-config EXEC command.

Using Flash Memory

The following provides information on the different functions of Flash memory that you might need
when configuring microcode:

•

Copying a New Image to the Flash Memory Card on a Cisco 7200 Series Router, page 36

•

Using Additional Flash Memory Commands, page 37

•

Recovering from Locked Blocks, page 38

Copying a New Image to the Flash Memory Card on a Cisco 7200 Series Router

Copying a new image to a Flash memory card might be required when a new microcode image becomes
available. Use the command copy tftp:filename [ bootflash | slot0 | slot1 ]:filename for the copy
procedure, where tftp:filename is the source of the file and [ bootflash | slot0 | slot1 ]:filename is the
destination in onboard Flash memory or on either of the Flash memory cards.

The following example shows the output from the copy tftp:filename command for Cisco IOS
Release 12.0:

Router# copy tftp:xcpa28-6 slot0:xcpa28-6

Address or name of remote host [181.23.250.2]?

Accessing tftp://181.23.250.2/jdoe/xcpa218-6...

Loading jdoe/xcpa218-6 from 181.23.250.2(via Ethernet3/0):!

Expanding slot0:/xcpa218-6_kernel_ecpa4 (472086 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_kernel_xcpa (414940 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_802 (246184 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_cmpc (562804 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_csna (96488 bytes):!!!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_eca (460712 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_offload (91976 bytes):!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_pca (68844 bytes):!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_push (15492 bytes):!!!

Expanding slot0:/xcpa218-6_seg_sslc (827760 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_tcpip (161196 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Expanding slot0:/xcpa218-6_seg_tn3270 (680672 bytes):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!

[OK - 4109312/8218624 bytes]

«
...
34
35
36
37
38
...
»

Содержание PA-4C-E









































Отзывы:

Нет отзывов

Похожие инструкции для PA-4C-E

Бренд: Wave wifi Страницы: 2

Бренд: ICP DAS USA Страницы: 8

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

Бренд: ZyXEL Communications Страницы: 116

Бренд: Teknim Страницы: 10

Бренд: Z Microsystems Страницы: 51

Бренд: Aewin Technologies Страницы: 86

Бренд: Teldat Страницы: 23

Бренд: Ubiquiti Страницы: 20

Бренд: KYLAND Technology Страницы: 19

Бренд: Flexwatch Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды