Cisco o UCS X440p Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 62

background image

C H A P T E R

2

Installing the Cisco UCS X440p PCIe Node

This chapter includes the following topics:

•

Installation Guides and Limitations, on page 9

•

PCIe Node Companion Module, on page 11

•

Replacing the Cisco UCS X440p PCIe Node, on page 11

•

PCIe Node Configuration, on page 14

Installation Guides and Limitations

Be aware of the following guidelines and limitations when installing the Cisco UCS X440p PCIe node.

• The Cisco UCS X440p PCIe node is supported in the Cisco UCS X9508 chassis only. Do not attempt

to install the PCIe node in any other UCS server chassis.

• The companion compute node host power should be off before attempting any removal or insertion

procedures. Hot removal or insertion of the PCIe node while the host is on is not supported.

• Each PCIe node must be paired with an X-Series compute node, and therefore, has specific configurations.

Either of the following configurations are supported. Be aware of these configurations, especially when
removing and installing compute nodes and PCIe nodes in your deployment.

Cisco UCS X440p PCIe Node Installation and Service Guide

9

«
...
15
16
17
18
19
...
»

Содержание o UCS X440p































































Отзывы:

Нет отзывов

Похожие инструкции для o UCS X440p

Бренд: Lattice Semiconductor Страницы: 15

iCE40 UltraLite

Бренд: Lattice Semiconductor Страницы: 13

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Бренд: Maxim Страницы: 14

Бренд: ZALMAN Страницы: 4

iTRON B 70.2040

Бренд: JUMO Страницы: 41

Бренд: Caen Страницы: 14

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Бренд: Belden Страницы: 84

Mercury FireWire 400

Бренд: OWC Страницы: 2

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Бренд: Hamlet Страницы: 11

Бренд: Eagle Technology Страницы: 39

cPCIS-1100 Series

Бренд: ADLINK Technology Страницы: 48

Бренд: Radica Games Страницы: 40

Бренд: Airvana Страницы: 90

Бренд: Renesas Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды