Cisco Nexus C9316D-GX Скачать руководство пользователя страница 44

Страница: 44 / 52

Specification

Characteristic

50, 60Hz

Nominal frequency

100-277VAC 13A Max, 240VDC – 380VDC 5.5A
Max

Maximum input current

35A (cold turn on); 50A (hot turn on)

Maximum inrush current

1100W @ 100 – 277VAC, 240VDC – 380VDC

Maximum continuous total output power

12V/ 90A

Output voltage

3.3V/ 3A

Standby output voltage

80 Plus Platinum

Efficiency

1100-W DC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PDC-1100W-PE

• NXA-PDC-1100W-PI

Specification

Characteristic

Nominal range: -54VDC (Range: -40 to -72 VDC)

DC input voltage range

32 A at -40 VDC

Maximum DC input current

1100 W

Maximum output power per power supply

90 A (cold turn on)

Maximum inrush current

4 ms at 100% load

Maximum hold-up time

12 V/ 90A

Power supply output voltage

3.3 V/ 3A

Power supply standby voltage

94% at 50% load

Efficiency rating @ -48VDC

Power Cable Specifications

The following sections specify the power cables that you can order and use with this switch.

Regulatory Standards Compliance Specifications

The following table lists the regulatory standards compliance for the switch.

Cisco Nexus C9316D-GX ACI-Mode Switch Hardware Installation Guide

System Specifications

1100-W DC Power Supply Specifications

Содержание Nexus C9316D-GX




















































Результаты поиска

Содержание Nexus C9316D-GX

Отзывы:

Похожие инструкции для Nexus C9316D-GX

Бренды по названию

Популярные бренды

Cisco Nexus C9316D-GX, Руководство по установке оборудования

Результаты поиска

Содержание Nexus C9316D-GX

Отзывы:

Похожие инструкции для Nexus C9316D-GX

Бренды по названию

Популярные бренды