Cisco Nexus 9364C-GX Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 64

background image

Either place the power supply on an antistatic surface or pack it in its packing materials.

Step 4

If the power supply slot is to remain empty, install a blank power supply filler panel (part number N2200-P-BLNK).

What to do next

You are ready to install the replacement power supply.

Removing an HVAC/HVDC Power Supply

You can remove one power supply while the other one provides power to the switch.

To disconnect the power supply from its power cables, you must shut off the power from the power source
and then either disconnect a connector for the power cables or release each of three cables from the power
supply (requires a standard screw driver).

Step 1

Turn off the circuit breaker for the power feed to the power supply that you are replacing.

Be sure that the LEDs turn off on the power supply that you are removing.

Step 2

Remove the power cable from the power supply by pressing the tab on the top of the Anderson Power SAF-D-Grid
connector and pull the cable and connector out of the power supply.

Step 3

Grasp the power supply handle while pressing the release latch towards the power supply handle.

Step 4

Place your other hand under the power supply to support it while you slide it out of the chassis.

Do not touch the electrical connectors on the back side of the module and prevent anything else from coming
into contact with and damaging the connectors.

Caution

What to do next

You are ready to install an HVAC/HVDC power supply in the open slot.

Removing a DC Power Supply

You can remove one power supply while the other one provides power to the switch.

To disconnect the power supply from its power cables, you must shut off the power from the power source
and then either disconnect a connector for the power cables or release each of three cables from the power
supply (requires a standard screw driver).

Step 1

Turn off the circuit breaker for the power feed to the power supply that you are replacing.

Be sure that the LEDs turn off on the power supply that you are removing.

Step 2

Remove the power cable from the power supply by doing the following:

• To remove an orange power cable connector from a 48-V DC power supply, do the following:

Cisco Nexus 9364C-GX ACI-Mode Switch Hardware Installation Guide

34

Replacing Components

Removing an HVAC/HVDC Power Supply

«
...
40
41
42
43
44
...
»

Содержание Nexus 9364C-GX

































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 9364C-GX

GuardSwitch 300 Series

Бренд: GE Страницы: 4

Бренд: OFFICINE OROBICHE Страницы: 7

Бренд: IDEC Страницы: 8

Бренд: IDEM SAFETY SWITCHES Страницы: 2

Бренд: Hall Technologies Страницы: 35

Бренд: Extron electronics Страницы: 2

A99-BAI-ACSF-UGKIT

Бренд: Westell Страницы: 3

Бренд: LOVATO ELECTRIC Страницы: 37

Sierra Video 1208V3S

Бренд: Kramer Страницы: 2

Бренд: Atlantis Land Страницы: 3

Бренд: NTI Страницы: 15

Draco tera compact 480 Series

Бренд: Ihse Страницы: 244

SANbox 5000 Series

Бренд: Qlogic Страницы: 2

Бренд: Clas Ohlson Страницы: 4

Бренд: ddtop Страницы: 10

Бренд: ELPRO Страницы: 8

Бренд: Uniclass Страницы: 32

Бренд: KYLAND Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды