Cisco Nexus 93180YC-FX3 Скачать руководство пользователя страница 8

Страница: 8 / 56

• 930-W port-side exhaust DC power supply with blue coloring (NXA-PDC-930W-PE)

• 930-W port-side intake DC power supply with burgundy coloring (NXA-PDC-930W-PI)

All fan modules and power supplies must use the same airflow direction.

Note

The following figure shows the switch features on the port side of the chassis.

48 100M/1/10/25-Gigabit
Ethernet SFP28 ports

1PPS and 10MHz SMB
ports

6 10/25/40/50/100-Gigabit
QSFP28 ports

GPS/GNSS antenna
connector

LEDs

GNSS, GPS, Time of Day, and PTP GM is not supported

Note

To determine which transceivers, adapters, and cables are support this switch, see the

Cisco Transceiver

Modules Compatibility Information

document.

The following figure shows the switch features on the power supply side of the chassis.

Management port (RJ45)

Power supply modules (1
or 2) (AC power supplies
shown) with slots
numbered 1 (left) and 2
(right)

USB port

Fan modules (4) with slots
numbered from 1 (left) to
4 (right)

Cisco Nexus 93180YC-FX3 NX-OS Mode Switch Hardware Installation Guide

Overview

Содержание Nexus 93180YC-FX3

























































Результаты поиска

Содержание Nexus 93180YC-FX3

Отзывы:

Похожие инструкции для Nexus 93180YC-FX3

Бренды по названию

Популярные бренды

Cisco Nexus 93180YC-FX3, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 93180YC-FX3

Отзывы:

Похожие инструкции для Nexus 93180YC-FX3

Бренды по названию

Популярные бренды