Cisco Nexus 7718 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 222

background image

Combined mode

The available power equals the combined output of all installed power supplies. There is no reserve
power. You activate this mode by using the

power redundancy-mode combined

command.

For example, if the power requirement for a switch is 5.2 kW and the switch has one 3-kW power
supply with 220 V input and 3.0-kW output, consider the following power planning scenarios:

•

Scenario 1

—

no added power supplies

If you do not add a power supply unit, the available power (3.0 kW) is insufficient for the switch
power requirement of 5.2 kW, so the switch powers the supervisor modules, fabric modules, and
fan trays, before powering as many I/O modules as the remaining available power can support
(one or more I/O modules will not be powered).

•

Scenario 2

—

install an extra 3-kW power supply

If you install an additional 3-kW power supply unit that can output 3.0 kW, the available power
becomes 6.0 kW. The increased amount of available power exceeds the switch power requirement
of 5.2 kW, so all of the modules and fan trays in the switch can power up.

The following table shows the results for each scenario.

Result

Reserve
Power

Available
Power

Power
Supply 2
Output

Power
Supply 1
Output

Power
Requirement

Scenario

Available power is less
than the power requirement
for the switch, so you
cannot power the entire
switch (some of the I/O
modules will not be able to
power up).

—

3.0 kW

—

3.0 kW

5.2 kW

1

Available power exceeds
the power requirement for
the switch, so the entire
switch can power up.

—

6.0 kW

3.0 kW

3.0 kW

5.2 kW

2

Cisco Nexus 7718 Switch Site Preparation and Hardware Installation Guide

OL-30453-01

85

Managing the Switch

Guidelines for Configuring Power Redundancy Modes

«
...
93
94
95
96
97
...
»

Содержание Nexus 7718































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 7718

Бренд: Painless Performance Products Страницы: 2

Switch 4500 Family

Бренд: 3Com Страницы: 742

Бренд: 3Com Страницы: 940

Бренд: 3Com Страницы: 43

OfficeConnect WX1200

Бренд: 3Com Страницы: 646

Бренд: IBM Страницы: 2

Бренд: Ubiquiti Страницы: 24

Бренд: Ubiquiti Страницы: 13

Бренд: Ubisys Страницы: 2

Бренд: Zektor Страницы: 65

Бренд: AVLT-Power Страницы: 12

CRSMEO-4 Series

Бренд: Festo Страницы: 16

Sierra Pro XL 1608V5S

Бренд: Kramer Страницы: 2

Бренд: S&S Northern Страницы: 8

Бренд: ICCN Страницы: 48

EdgeSwitch 8 150W

Бренд: Ubiquiti Страницы: 28

Бренд: Intellinet Страницы: 12

Бренд: IMI SENSORS Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды