background image

 

 

 

 

Cisco MCS-78XX Boot Error Codes 

Contents 

Introduction

 

 

Prerequisites

 

 

      

Requirements

  

      

Components Used

  

      

Conventions

  

POST

 

 

POST Error Message

 

 

NetPro Discussion Forums - Featured Conversations

 

 

Related Information

 

 

Introduction  

This document is designed to help you determine the root cause of bootup 
issues on the Cisco Media Convergence Server (MCS)-78xx servers.  

Prerequisites  

Requirements  

Cisco recommends that you have knowledge of this topic: 

z

Cisco MCS-78xx server administration  

Components Used  

The information in this document is based on these software and hardware versions:  

z

Cisco MCS-78xx series servers  

z

Cisco MCS-78xx Operating System (OS) V2000.x or later  

The information in this document was created from the devices in a specific lab environment. All of the 
devices used in this document started with a cleared (default) configuration. If your network is live, 
make sure that you understand the potential impact of any command. 

Conventions  

TAC Notice:

 What's 

Changing on TAC Web

 

Help us help you.

Please rate this 

document.

Excellent

Good

Average

Fair

Poor

This document solved 

my problem.

Yes

No

Just browsing

Suggestions for 
improvement:

 (256 character limit)

 

Send

Page 1 of 13

Cisco - Cisco MCS-78XX Boot Error Codes

10/2/2008

http://kbase.cisco.com/paws/servlet/ViewFile/12138/mcs_boot.xml?convertPaths=1

Содержание MCS-78 Series














Отзывы: