manualshive.com logo in svg

Cisco IE 4000, Руководство по установке оборудования, Страница: 28 / 78

Поделиться
Скачать
Cisco IE 4000 Скачать руководство пользователя страница 28

24

Switch Installation

 

Connecting to Power

Figure 9

Stripping the Power Connection Wire

5.

Remove the two captive screws that attach the power connector to the switch, and remove the power connector. 
Remove both connectors if you are connecting to two power sources. See 

Figure 10 on page 24

.

Figure 10

Removing the Power Connectors from the Switch

6.

On the power connector, insert the exposed part of the positive wire into the connection labeled “+” and the exposed 
part of the return wire into the connection labeled “–”. See 

Figure 11 on page 25

. Make sure that you cannot see any 

wire lead. Only wire 

with

 

insulation

 should extend from the connector.

Warning: 

An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that 

no exposed portion of the DC-input power source wire extends from the connector(s) or terminal block(s). 
Statement 122

974

8

9

1

1

0.25 in. (6.3 mm) ± 0.02 in. (0.5 mm)

1

Power Connectors

Содержание IE 4000















































































Отзывы:

Нет отзывов