manualshive.com logo in svg

Cisco IE 4000, Руководство по установке оборудования, Страница: 17 / 78

Поделиться
Скачать
Cisco IE 4000 Скачать руководство пользователя страница 17

13

Cisco Systems, Inc.

www.cisco.com

 

Switch Installation

This chapter describes how to install your switch, verify the boot fast, and connect the switch to other devices. It also 
includes information specifically for installations in hazardous environments.

Read these topics, and perform the procedures in this order:

Preparing for Installation, page 13

Installing or Removing the Flash Memory Card (Optional), page 16

Connecting to a Console Port (Optional), page 17

Connecting to Power, page 18

Installing the Switch, page 29

Connecting Alarm Circuits, page 31

Connecting Destination Ports, page 35

Verifying Switch Operation, page 39

Where to Go Next, page 39

Preparing for Installation

This section provides information about these topics:

Warnings, page 13

Installation Guidelines, page 15

Installation Guidelines, page 15

Verifying Package Contents, page 16

Warnings

These warnings are translated into several languages in the 

Regulatory Compliance and Safety Information 

for this 

switch.

Warning: 

Before working on equipment that is connected to power lines, remove jewelry (including rings, 

necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious 
burns or weld the metal object to the terminals. Statement 43

Warning: 

Exposure to some chemicals could degrade the sealing properties of materials used in the sealed relay 

device. Statement 381

Warning: 

Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 

1001

Содержание IE 4000















































































Отзывы:

Нет отзывов