background image

C H A P T E R

1-1

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

1

Installing the FlexWAN and Enhanced FlexWAN 
Modules

This chapter contains the following sections:

Preparing to Install the FlexWAN or Enhanced FlexWAN Module, page 1-1

Installing the FlexWAN and Enhanced FlexWAN Modules, page 1-3

Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter, page 1-6

Preparing to Install the FlexWAN or Enhanced FlexWAN 
Module

Note

Before you can install the FlexWAN or Enhanced FlexWAN modules, you must install at least one 
supervisor engine in the chassis. Throughout this publication, the term 

supervisor engine

 refers to 

Supervisor 720 Engine.

The following tools adn equipment are required to install the FlexWAN and Enhanced FlexWAN 
modules:

3/16-inch flat-blade screwdriver for the captive installation screws on the FlexWAN and Enhanced 
FlexWAN modules.

Antistatic mat or antistatic foam.

Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist 
strap included with all upgrade kits, field-replaceable units (FRUs), and spares.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are 
improperly handled, results in complete or intermittent failures. Port adapters and processor 
modules consist of printed circuit boards that are fixed in metal carriers. Electromagnetic 
interference (EMI) shielding and connectors are integral components of the carrier. Although the 
metal carrier helps to protect the board from ESD, use a preventive antistatic strap during handling. 

Содержание Enhanced FlexWAN











Отзывы: