Cisco CRS Series Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 54

Cisco CRS Series Скачать руководство пользователя страница 50

Power Up and Power Down a Chassis

This section describes how to power up and power down a chassis with an AC or DC power shelf. For details
on the chassis power systems, see the

Basic Chassis Power Details, on page 1

, the

AC Power Systems, on

page 8

, and the

DC Power Systems, on page 6

. For complete information on regulatory compliance and

safety, see

Regulatory Compliance and Safety Information for the Cisco CRS Carrier Routing System

.

Most components on the chassis, such as the PMs, alarm modules, and fan trays, can be removed or installed
in the chassis while it is running. Although it is possible to install or remove a power shelf while the chassis
is running, it is recommended to remove power from the chassis completely, if possible, for service protection
and safety.

Figure 35: Cisco CRS Enhanced 16-Slot Line Card Chassis Front (PLIM) Side Slot Numbers, on page 50

shows the chassis slot number on the front (PLIM) side of the Cisco CRS Series Enhanced 16-slot Line Card
Chassis with an AC and DC power system installed.

Figure 35: Cisco CRS Enhanced 16-Slot Line Card Chassis Front (PLIM) Side Slot Numbers

Table 2: PM LED Status Indicator LightS, on page 51

shows the LED status indicator lights for the AC and

DC PMs in a power supply.

Cisco CRS Routers 16-Slot Line Card Chassis Enhanced Router Installation Guide

50

Installing Power Components

Power Up and Power Down a Chassis

«
...
48
49
50
51
52
...
»

Содержание CRS Series























































Отзывы:

Нет отзывов