Cisco CRS Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 54

Cisco CRS Series Скачать руководство пользователя страница 6

DC Power Systems

The Cisco CRS Series Enhanced 16-slot Line Card Chassis DC power system can provide up to 16,800 watts
to power the chassis. However, by default, the power capability of a system when shipped, with six DC PMs
per power shelf, is 12,600 watts.

Depending on the hardware deployed at your site, your system may not consume the maximum power
supplied by the power system.

Note

Each DC powered chassis contains two DC power shelves for 2N redundancy. The shelves contain the input
power connectors. Each shelf can accept up to eight DC PMs. The power shelves and DC PMs are field
replaceable.

Figure 3: DC Power Shelf Cable Wiring for Power Shelf , on page 6

shows the cable wiring for the power

shelf.

Figure 3: DC Power Shelf Cable Wiring for Power Shelf

Each power shelf operates with up to eight DC inputs of

–

48/

–

60 VDC (nominal), 60A. The power shelf

accepts input DC power in the range

–

40 to

–

72 VDC.

Table 1: DC Input Current and Voltage Information, on page 7

lists the DC input current and voltage

specifications.

Cisco CRS Routers 16-Slot Line Card Chassis Enhanced Router Installation Guide

6

Installing Power Components

DC Power Systems

«
...
4
5
6
7
8
...
»

Содержание CRS Series























































Отзывы:

Нет отзывов