Cisco CRS Series Скачать руководство пользователя страница 51

Страница: 51 / 54

Table 2: PM LED Status Indicator LightS

Function or Meaning

Color

LED Name

On: The input voltage is present
and within regulation range.

Blinking: The input voltage is
present but out of regulation range.

Off: The input voltage is not
present.

Green

Input_OK

On: The output voltage is on.

Blinking: The PM is in a power
limit or an OC condition.

Off: The output voltage is off.

Green

Output_OK

On: An internal fault is detected
within the PM.

Off: The PM has no internal fault.

Red

Internal Fault

Power Up a Chassis

This section describes how to power up a chassis with AC or DC power shelves installed.

Prerequisites

Before performing this task, perform the following procedures:

If you have a DC power system installed, wiring at the BDFB or at the power plant should be complete.

Steps

To power on the chassis, perform the following steps:

Cisco CRS Routers 16-Slot Line Card Chassis Enhanced Router Installation Guide

Installing Power Components

Power Up a Chassis

Содержание CRS Series























































Результаты поиска

Содержание CRS Series

Отзывы:

Cisco CRS Series, Руководство по установке, Страница: 51 / 54

Результаты поиска

Содержание CRS Series

Отзывы: