Cisco Catalyst 7500 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

background image

10 Replacing the Chassis Interface (CI) Board in the Cisco 7500 Series Chassis

Replacing the CI in the Cisco 7505

Removing and Replacing the Power Harness Cover and Power Harness

You must remove the power harness cover to access either the power supply or the CI. A single M-3
Phillips screw secures the power harness cover to the backplane cover.

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug

the power cord. (For a translation of this safety warning, refer to the section “Translated Safety
Warnings” on page 32.)

Follow these steps to remove and replace the power harness cover:

Step 1

Turn OFF the system power switch and unplug the power cable from the power source.

Step 2

To remove the chassis cover panel, follow Steps 1 and 2 in the section “Removing and
Replacing the Chassis Cover Panel” on page 6.

Step 3

Use a number 1 Phillips screwdriver to remove the M-3 screw that secures the top of the
harness cover to the backplane. (See the cutaway in Figure 5.)

Figure 5

Removing the Power Harness Cover

Step 4

Holding the cover with one hand, tilt the top of the cover back toward you, then pull it
upward slightly so that the tab clears the slot in the chassis floor.

Step 5

When the tab clears the slot, pull the cover straight back off the harness and out of the
chassis.

Note

Move on to the required procedure, depending on the work you need to do. Then to replace

the power harness and power harness cover, proceed to Step 6, which follows.

Power harness
cover

Arbiter/chassis
interface board
cover

Power supply

Fan tray

Removing power harness cover

H2867

«
...
8
9
10
11
12
...
»

Содержание Catalyst 7500 Series









































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 7500 Series

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Nedap Страницы: 20

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренд: R82 Страницы: 11

Бренд: Radionics Страницы: 14

Бренд: PUTCO Страницы: 2

Бренд: GBD Страницы: 60

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

ZoneSense Plus AS

Бренд: Halma Страницы: 58

Бренд: McIntosh Страницы: 68

Бренд: Hard Head Страницы: 10

Бренд: A&D Страницы: 42

Бренд: Cruisair Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды