manualshive.com logo in svg

Cisco Catalyst 3550 Series, Руководство по настройке программного обеспечения, Страница: 697 / 992

Поделиться
Скачать
Cisco Catalyst 3550 Series Скачать руководство пользователя страница 697

 

31-19

Catalyst 3550 Multilayer Switch Software Configuration Guide

78-11194-09

Chapter 31      Configuring IP Unicast Routing

Configuring RIP

Configuring RIP

The Routing Information Protocol (RIP) is an interior gateway protocol (IGP) created for use in small, 
homogeneous networks. It is a distance-vector routing protocol that uses broadcast User Datagram 
Protocol (UDP) data packets to exchange routing information. The protocol is documented in RFC 1058. 
You can find detailed information about RIP in IP Routing Fundamentals, published by Cisco Press.

Note

RIP is the only routing protocol supported by the SMI; other routing protocols require the EMI on the 
switch.

Using RIP, the switch sends routing information updates (advertisements) every 30 seconds. If a router 
does not receive an update from another router for 180 seconds or more, it marks the routes served by 
that router as unusable. If there is still no update after 240 seconds, the router removes all routing table 
entries for the non-updating router. 

RIP uses hop counts to rate the value of different routes. The hop count is the number of routers that can 
be traversed in a route. A directly connected network has a hop count of zero; a network with a hop count 
of 16 is unreachable. This small range (0 to 15) makes RIP unsuitable for large networks.

If the router has a default network path, RIP advertises a route that links the router to the pseudonetwork 
0.0.0.0. The 0.0.0.0 network does not exist; it is treated by RIP as a network to implement the default 
routing feature. The switch advertises the default network if a default was learned by RIP or if the router 
has a gateway of last resort and RIP is configured with a default metric. RIP sends updates to the 
interfaces in specified networks. If an interface’s network is not specified, it is not advertised in any 
RIP update.

This section briefly describes how to configure RIP. It includes this information:

•

Default RIP Configuration, page 31-19

•

Configuring Basic RIP Parameters, page 31-20

•

Configuring RIP Authentication, page 31-22

•

Configuring Summary Addresses and Split Horizon, page 31-22

Default RIP Configuration

Table 31-5

 shows the default RIP configuration.

Table 31-5

Default RIP Configuration

Feature

Default Setting

Auto summary

Enabled.

Default-information originate

Disabled.

Default metric

Built-in; automatic metric translations.

IP RIP authentication key-chain

No authentication.

Authentication mode: clear text.

IP RIP receive version

According to the version router configuration command.

IP RIP send version

According to the version router configuration command.

IP RIP triggered

According to the version router configuration command.

Содержание Catalyst 3550 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов