manualshive.com logo in svg

Cisco Catalyst 3550 Series, Руководство по настройке программного обеспечения, Страница: 277 / 992

Поделиться
Скачать
Cisco Catalyst 3550 Series Скачать руководство пользователя страница 277

 

12-13

Catalyst 3550 Multilayer Switch Software Configuration Guide

78-11194-09

Chapter 12      Configuring VLANs

Configuring Extended-Range VLANs

•

VLANs in the extended range are not supported by VQP. They cannot be configured by VMPS.

•

STP is enabled by default on extended-range VLANs, but you can disable it by using the no 
spanning-tree vlan vlan-id global configuration command. When the maximum number of 
spanning-tree instances(128) are on the switch, spanning tree is disabled on any newly created 
VLANs. If the number of VLANs on the switch exceeds the maximum number of spanning tree 
instances, we recommend that you configure the IEEE 802.1S Multiple STP (MSTP) on your switch 
to map multiple VLANs to a single STP instance. For more information about MSTP, see 

Chapter 17, “Configuring MSTP.”

•

Each routed port on a Catalyst 3550 switch creates an internal VLAN for its use. These internal 
VLANs use extended-range VLAN numbers, and the internal VLAN ID cannot be used for an 
extended-range VLAN. If you try to create an extended-range VLAN with a VLAN ID that is 
already allocated as an internal VLAN, an error message is generated, and the command is rejected.

–

Because internal VLAN IDs are in the lower part of the extended range, we recommend that you 
create extended-range VLANs beginning from the highest number (4094) and moving to the 
lowest (1006) to reduce the possibility of using an internal VLAN ID.

–

Before configuring extended-range VLANs, enter the show vlan internal usage privileged 
EXEC command to see which VLANs have been allocated as internal VLANs.

–

If necessary, you can shut down the routed port assigned to the internal VLAN, which frees up 
the internal VLAN, and then create the extended-range VLAN and re-enable the port, which 
then uses another VLAN as its internal VLAN. See the 

“Creating an Extended-Range VLAN 

with an Internal VLAN ID” section on page 12-14

.

Creating an Extended-Range VLAN

You create an extended-range VLAN in global configuration mode by entering the vlan global 
configuration command with a VLAN ID from 1006 to 4094. This command accesses the config-vlan 
mode. The extended-range VLAN has the default Ethernet VLAN characteristics (see 

Table 12-2

) and 

the MTU size is the only parameter you can change. Refer to the description of the vlan global 
configuration command in the command reference for defaults of all parameters. If you enter an 
extended-range VLAN ID when the switch is not in VTP transparent mode, an error message is 
generated when you exit from config-vlan mode, and the extended-range VLAN is not created. 

Extended-range VLANs are not saved in the VLAN database; they are saved in the switch running 
configuration file. You can save the extended-range VLAN configuration in the switch startup 
configuration file by using the copy running-config startup-config privileged EXEC command.

Note

Before you create an extended-range VLAN, you can verify that the VLAN ID is not used internally by 
entering the show vlan internal usage privileged EXEC command. If the VLAN ID is used internally 
and you want to free it up, go to the

“Creating an Extended-Range VLAN with an Internal VLAN ID” 

section on page 12-14

 before creating the extended-range VLAN.

Beginning in privileged EXEC mode, follow these steps to create an extended-range VLAN:

Command

Purpose

Step 1

configure terminal

Enter global configuration mode.

Step 2

vtp mode transparent

Configure the switch for VTP transparent mode, disabling VTP.

Содержание Catalyst 3550 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов