Cisco ASR 1001-X Скачать руководство пользователя страница 139

Страница: 139 / 152

Description

Direction

Signal

Pin

unused

Input

DSR

Clear to Send (tied to
RTS)

Input

CTS

Cisco ASR 1002 Router Auxiliary Port Signals and Pinouts

Unless stated otherwise, the specifications for the Cisco ASR 1002-X Router are the same as the Cisco
ASR 1002 Router specifications listed in this section.

Note

The following table lists the pinout of the dual RJ-45 ports for the auxiliary port signals.

Table 42: Auxiliary Port Pinouts for Cisco ASR 1002 Router

Description

Direction

Signal

Pin

Request to Send

Output

RTS

Data Terminal Ready
(always On)

Output

DTR

Transmit Data

Output

TXD

Ring Indicator

—

GND

Receive Data

Input

RXD

Data Set Ready/Data
Carrier Detect

Input

DSR/DCD

Clear to Send

Input

CTS

Cisco ASR 1002 Router BITS Port Signals and Pinouts

Table 43: BITS RJ-45 Interface Pinouts for Cisco ASR 1002 Router

Description

Direction

Signal

Pin

Receive Ring

Input

RX Ring

Cisco ASR 1001-X Router Hardware Installation Guide

131

Cisco ASR 1001-X Router Specifications

Cisco ASR 1002 Router Auxiliary Port Signals and Pinouts

Содержание ASR 1001-X
























































































































































Результаты поиска

Содержание ASR 1001-X

Отзывы:

Cisco ASR 1001-X, Руководство по установке оборудования, Страница: 139 / 152

Результаты поиска

Содержание ASR 1001-X

Отзывы: