manualshive.com logo in svg

Cisco ASR 1001-X, Руководство по установке оборудования, Страница: 100 / 152

Поделиться
Скачать
Cisco ASR 1001-X Скачать руководство пользователя страница 100

When you install the unit, the ground connection must always be made first and disconnected last. Statement
1046

Danger

Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003

Danger

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030

Danger

Removing AC Power Supplies from the Cisco ASR 1001-X Router

This section describes how to remove an AC power supply from the Cisco ASR 1001-X Router. The Cisco
ASR 1001-X Router has two power supply slots, power supply slot 0 (PS0) next to the Standby switch and
power supply slot 1 (PS1) to the right, as shown in the below figures.

The Cisco ASR 1001-X Router has redundant power supplies that can be hot-swapped.

Note

Follow these steps to remove an AC power supply from the Cisco ASR 1001-X Router:

SUMMARY STEPS

1.

At the rear of the router, ensure that the power switch is in the Standby position.

2.

Unplug the power cable from the power supply as shown in the below figure.

3.

Press the retaining latch towards the pull handle, grasp the handle with one hand, and pull the power supply
out of the slot while supporting the weight of the power supply with the other hand, as shown in the below
figure.

4.

Repeat these steps if it is required to remove the other AC power supply.

DETAILED STEPS

Step 1

At the rear of the router, ensure that the power switch is in the Standby position.

It is not required to place the power switch in the Standby position if you want to hot-swap a single power
supply.

Note

   Cisco ASR 1001-X Router Hardware Installation Guide

92

Removing and Replacing FRUs from the Cisco ASR 1001-X Router

Removing AC Power Supplies from the Cisco ASR 1001-X Router

Содержание ASR 1001-X

























































































































































Отзывы:

Нет отзывов