background image

C H A P T E R

 

3-1

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

3

Installing the Cisco AS5400XM Universal 
Gateway

This chapter guides you through the installation of the Cisco AS5400XM universal gateway and includes 
the following sections: 

Setting Up the Chassis, page 3-1

 

Connecting to the Network, page 3-5

Connecting the Console Terminal and Modem, page 3-9

Connecting to the BITS Port, page 3-10

Connecting to the Alarm Port, page 3-11

Supplying Power, page 3-12

Where to Go Next, page 3-15

Warning

Only trained and qualified personnel should be allowed to install or replace this equipment. 

Statement 49

Warning

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during 
normal use. 

Statement 39

Warning

Incorrect connection of this or connected equipment to a general purpose outlet could result in a 
hazardous situation. 

Statement 87

Setting Up the Chassis

You can set the chassis on a desktop or install it in a rack. Use the procedure in this section that best 
meets the needs of your network: 

Setting the Chassis on a Desktop

Rack-Mounting the Chassis

Содержание AS5400XM

















Отзывы: