Cisco AIR-CAP3702E-A-K9 Скачать руководство пользователя | Manualshive

Страница: 12 / 44

background image

12

•

Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a
desktop.

Note

You can mount the access point above a suspended ceiling but you must purchase
additional mounting hardware: See

“Mounting the Access Point” section on page 15

for

additional information.

•

Access point power options: power supplied by the recommended external power supply (Cisco
AIR-PWR-B), a DC power supply, PoE from a network device, or a PoE power injector/hub
(usually located in a wiring closet).

Note

Access points mounted in a building’s environmental airspace must be powered using PoE
to comply with safety regulations.

Cisco recommends that you make a site map showing access point locations so that you can record the
device MAC addresses from each location and return them to the person who is planning or managing
your wireless network.

Installation Summary

Installing the access point involves these operations:

•

Performing a pre-installation configuration (optional)

•

Mounting the access point

•

Grounding the access point

•

Deploying the access point on the wireless network

Performing a Pre-Installation Configuration

The following procedures ensure that your access point installation and initial operation go as
expected. A pre-installation configuration is also known as

priming the access point

. This procedure

is optional.

Note

Performing a pre-installation configuration is an optional procedure. If your network
controller is properly configured, you can install your access point in its final location and
connect it to the network from there. See the

“Deploying the Access Point on the Wireless

Network” section on page 15

for details.

«
...
10
11
12
13
14
...
»

Содержание AIR-CAP3702E-A-K9













































Отзывы:

Нет отзывов

Похожие инструкции для AIR-CAP3702E-A-K9

Бренд: Cambium Networks Страницы: 5

Бренд: Cambium Networks Страницы: 44

Бренд: Sagido Страницы: 82

DAP-2553 - Wireless N Dual Band Gigabit Access...

Бренд: D-Link Страницы: 32

Бренд: Ubiquiti Страницы: 63

Бренд: Caimore Страницы: 83

Бренд: Aruba Страницы: 15

Бренд: H3C Страницы: 19

Бренд: ZyXEL Communications Страницы: 109

Бренд: Loopcomm Страницы: 68

Бренд: Cisco Страницы: 9

Бренд: Cisco Страницы: 12

Small Business WAP551

Бренд: Cisco Страницы: 4

Linksys WRT120N

Бренд: Cisco Страницы: 35

Бренд: Cisco Страницы: 17

Бренд: Cisco Страницы: 2

Linksys WRT54GS2

Бренд: Cisco Страницы: 6

Бренд: Cisco Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды