Cisco AIR-CAP3702E-A-K9 Скачать руководство пользователя | Manualshive

Страница: 29 / 44

background image

29

This device complies with Class B Limits of Industry Canada. Operation is subject to the following
two conditions:

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received, including interference that may cause undesired
operation.

Cisco Aironet Access Points are certified to the requirements of RSS-210. The use of this device in a
system operating either partially or completely outdoors may require the user to obtain a license for
the system according to the Canadian regulations. For further information, contact your local Industry
Canada office.

This device has been designed to operate with antennas having a maximum gain of 6 dBi. Antennas
having a gain greater than 6 dBi are strictly prohibited for use with this device. The required antenna
impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful
communication.

Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.

Users are advised that high-power radars are allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or
damage to LE-LAN devices.

French Translation

Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du
Canada.

Cet appareil respecte les limites prescrites pour les appareils de classe B par Industrie Canada. Son
utilisation est soumise aux deux conditions suivantes :

(1) Cet appareil ne doit pas causer d’interf_rences nuisibles, et

(2) Cet appareil doit accepter toutes les interf_rences, y compris celles susceptibles de perturber le
fonctionnement de l’appareil.

Les points d'acc_s Aironet de Cisco sont certifi_s conform_ment aux exigences du CNR-210.
L'utilisation de cet appareil dans un syst_me fonctionnant partiellement ou enti_rement ˆ l'ext_rieur
peut n_cessiter l'obtention d'une licence pour le syst_me, conform_ment ˆ la r_glementation
canadienne. Pour plus de renseignements, communiquez avec le bureau local d'Industrie Canada.

Cet appareil a _t_ con_u pour fonctionner avec une antenne d'un gain maximum de 6 dBi. Il est
strictement interdit d'utiliser des antennes ayant un gain sup_rieur ˆ 6 dBi avec cet appareil. L'antenne
doit avoir une imp_dance de 50 ohms.

«
...
27
28
29
30
31
...
»

Содержание AIR-CAP3702E-A-K9













































Отзывы:

Нет отзывов

Похожие инструкции для AIR-CAP3702E-A-K9

Бренд: Magnadyne Страницы: 8

Бренд: UNICOM Страницы: 56

Nfiniti AirStation WZR-AGL300NH

Бренд: Buffalo Tech Страницы: 24

Thunderbolt 3/USB-C I/ O CARD

Бренд: Logicube Страницы: 5

Бренд: SIYI Страницы: 28

Бренд: Zonet Страницы: 9

802.11g Wireless Access Point WAP253

Бренд: Abocom Страницы: 1

Бренд: Airlink101 Страницы: 15

Бренд: TRENDnet Страницы: 14

ConnectPort X2e Wi-Fi

Бренд: Digi Страницы: 2

Бренд: RadioLabs Страницы: 9

AIR-CAP3501E-A-K9

Бренд: Cisco Страницы: 34

AIR-AP1210 - Aironet 1200 - Wireless Access Point External

Бренд: Cisco Страницы: 35

Aironet 1520 Series

Бренд: Cisco Страницы: 66

Бренд: Cisco Страницы: 44

AIR-CAP1552H-x-K9

Бренд: Cisco Страницы: 24

AIR-AP1542D-*-K9

Бренд: Cisco Страницы: 72

AIR-AP1010 - 1000 Series Lightweight Access Point

Бренд: Cisco Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды