Cisco AIR-AP1020 - 1000 Series Lightweight Access Point Скачать руководство пользователя страница 14

Страница: 14 / 44

Installation and Configuration

Collecting Required Tools and Supplies

AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide

78-17147-01

Collecting Required Tools and Supplies

This section describes the tools and information that you should have before installing the access point.

•

One Cisco Aironet 1000 Series lightweight access point per location.

•

Cisco Aironet 1000 Series lightweight access point Mounting Kits, factory-supplied with each Cisco
Aironet 1000 Series lightweight access point.

•

Optional Cisco Aironet 1000 Series lightweight access point Mounting Kits, factory-orderable.

•

Optional AC-to-DC external power supplies, factory-orderable. Note that this option requires the
power cable to be run through the plenum in a metal conduit to meet safety requirements.

•

Map showing Cisco Aironet 1000 Series lightweight access point locations and mounting and power
options.

•

Screwdrivers, drills, and ladder.

•

An assortment of sheet metal and drywall screws and toggle bolts.

•

CAT-5 (or higher) cables to connect the Cisco Aironet 1000 Series lightweight access point locations
and other network devices.

•

Optional Kensington MicroSaver Security Cable to secure each Cisco Aironet 1000 Series
lightweight access point.

Continue with “

Pre-Installation Configuration

Содержание AIR-AP1020 - 1000 Series Lightweight Access Point













































Результаты поиска

Содержание AIR-AP1020 - 1000 Series Lightweight Access Point

Отзывы:

Похожие инструкции для AIR-AP1020 - 1000 Series Lightweight Access Point

Бренды по названию

Популярные бренды

Cisco AIR-AP1020 - 1000 Series Lightweight Access Point, Быстрый старт

Результаты поиска

Содержание AIR-AP1020 - 1000 Series Lightweight Access Point

Отзывы:

Похожие инструкции для AIR-AP1020 - 1000 Series Lightweight Access Point

Бренды по названию

Популярные бренды