manualshive.com logo in svg

Cisco 4006 - Catalyst Switch, Руководство по настройке, Страница: 209 / 614

Поделиться
Скачать
Cisco 4006 - Catalyst Switch Скачать руководство пользователя страница 209

C H A P T E R

 

10-1

Catalyst 4500 Series,  Catalyst 2948G, Catalyst 2948G-GE-TX,  and Catalyst 2980G Switches Software Configuration Guide—Release 8.2GLX

78-15908-01

10

Configuring VLANs

This chapter describes how to configure virtual LANs (VLANs) on the Catalyst enterprise LAN 
switches.

Note

For complete syntax and usage information for the commands that are used in this chapter, refer to the 
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2948G-GE-TX,  and Catalyst 2980G Switches Command 
Reference.

This chapter contains these sections:

•

Understanding How VLANs Work, page 10-1

•

VLAN Default Configuration, page 10-4

•

VLAN Configuration Guidelines, page 10-5

•

Configuring VLANs on the Switch, page 10-6

•

Configuring Auxiliary VLANs, page 10-13

 

•

Configuring Private VLANs, page 10-16

Understanding How VLANs Work

A VLAN is a group of end stations with a common set of requirements, independent of physical location. 
A VLAN has the same attributes as a physical LAN, but allows you to group end stations even if the 
VLANs are not located physically on the same LAN segment.

VLANs allow you to group ports on a switch to limit unicast, multicast, and broadcast traffic flooding. 
Flooded traffic originating from a particular VLAN is only flooded out other ports belonging to that 
VLAN.

Note

Before you create VLANs, you must decide whether to use VLAN Trunking Protocol (VTP) or VLAN 
Management Policy Server (VMPS) to maintain global VLAN configuration information for your 
network. For more information on VTP, see 

Chapter 9, “Configuring VTP.”

 For more information on 

VMPS, see 

Chapter 12, “Configuring Dynamic VLAN Membership with VMPS.”

Figure 10-1

 shows an example of VLANs that are segmented into logically defined networks.

Содержание 4006 - Catalyst Switch







































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов