manualshive.com logo in svg

Cirronet CR-SEH, Руководство пользователя

Поделиться
Скачать
Cirronet CR-SEH Скачать руководство пользователя страница 29

CR-SEH 

and is the default. 

24

 is the minimum value and 

48

 is the maximum value. The dwell time is 

changed to optimize the data throughput for a given installation. 

set

 selects a limited frequency band to be used. The default value is 1 which uses the entire 

frequency. For operation in France use a value of 8 and for Israel and Canada, use a value of 
9. The CR-SEH radio also has 6 hop sets that avoid 802.11b channels. This allows the CR-
SEH to operate in environments with an 802.11b network without interfering with the 
802.11b network. The table below provides details of the hop sets. 

Hop 
Set  

Frequency Range

 

802.11b Channels 
Avoided 

# of Channels 

0 

2400 – 2483MHz 

None 

43 

1 

2430 – 2483MHz  

2412MHz, 2417MHz 

27 

2 

2400 – 2410, 2440 – 2483MHz 

2422MHz, 2427MHz 

27 

3 

2400 – 2420, 2450 – 2483MHz 

2432MHz, 2437MHz 

27 

4 

2400 – 2430, 2460 – 2483MHz 

2442MHz, 2447MHz 

27 

5 

2400 – 2440, 2470 – 2483MHz 

2452MHz, 2457MHz 

27 

6 

2400 – 2450, 2480 – 2483MHz 

2462MHz, 2467MHz 

27 

7 Reserved 

 

 

8 

2422 – 2447MHz (France, 
Israel) 

 15 

9 

2453 – 2479MHz (Canada, 
Mexico) 

 15 

 

The frequency of the 802.11b channel avoided refers to the center frequency of the 802.11b 
channel. 

slave 

list

 displays the serial numbers of the radios in the CR-SEHs that are currently registered 

with the CR-SEH. 

disconnect

 terminates the connection between the master CR-SEH and 

the slave CR-SEH with the radio serial identification number entered. The radio serial 
identification number must be entered with the “-“’s and can be found using 

list

.  

sync 

These commands set the operation of the synchronization signal used in co-located CR-SEH 
networks. The default mode is the sync OFF. Sync is enabled by selecting a synchronization 

master

. Synchronization will occur over the RS-485 SYNC lines. One co-located master 

CR-SEH must be configured as the sync master. If sync has been enabled, the other co-
located master CR-SEHs will listen for a sync signal from the sync master. If no sync is 
heard, a co-located master CR-SEH will make itself a sync master and provide a sync signal. 
This is called the master backup override mode. 

override

 toggles the master backup 

override on and off. The default mode is ON. In standalone CR-SEH installations, 
synchronization is not required and should be left disabled.

 

 2000- 2004 Cirronet

 Inc 

24 

M-2411-0013 Rev A 

 

Содержание CR-SEH



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды