background image

3

Instruction Manual

computer MAX

 SAFETY PRECAUTIONS

DANGER

Warns of a risk, which could result in personal injury or material damage.

ATTENTION

Indicates that special attention should be paid to a specifi c point.

Follow the warnings described in this manual with the symbols shown below.

If you must handle the unit for its installation, start-up or maintenance, the following 

should be taken into consideration:

Incorrect handling or installation of the unit may result in injury to personnel as well as damage 

to the unit. In particular, handling with voltages applied may result in electric shock, which may 

cause death or serious injury to personnel. Defective installation or maintenance may also 

lead to the risk of fi re.

Read the manual carefully prior to connecting the unit. Follow all installation and maintenance 

instructions throughout the unit’s working life. Pay special attention to the installation stan-

dards of the National Electrical Code.

Refer to the instruction manual before using the unit

In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can 

result in injury or damage to the unit and /or installations.

CIRCUTOR, SA reserves the right to modify features or the product manual without prior notifi cation.

 DISCLAIMER

CIRCUTOR, SA

 reserves the right to make modifi cations to the device or the unit specifi ca-

tions set out in this instruction manual without prior notice. 

CIRCUTOR, SA

 on its web site, supplies its customers with the latest versions of the device 

specifi cations and the most updated manuals.                                 

 

 

 

 

 

 

           www.circutor.com

CIRCUTOR, 

recommends using the original cables and accessories that are 

supplied with the device.

Содержание computer MAX 12



































Отзывы: