CIRCUIT DESIGN MU-4-434 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 88

CIRCUIT DESIGN MU-4-434 Скачать руководство пользователя страница 49

OG_MU-4-434_v10e Circuit Design, Inc.

49

OPERATION GUIDE

5.4.3 Monitor commands and Responses

5.4.3.1 @CA Target station all channel RSSI absolute level measurement

The RSSI (Received Signal Strength Intensity) of the specified target station is measured over all channels. It is
possible to check the floor noise level of the field, third party field strength, and noise level of the system itself. The
RSSI value is the received strength of the radio waves inducted through the antenna of the target station. The
measured value is output as a 2-digit hexadecimal number in ASCII characters that expresses the absolute value for
RSSI. The code of the RSSI value acquired is minus.

Format 1: ‘@’ + ‘CA’ + ‘/’ + route infor ‘CRLF’
Format 2: ‘@’ + ‘CA’ + ‘CRLF’

Details

Format1: ‘@CA’ ‘/’ rr,rr,...,rr ‘

C

R

L

F

’

Format2: ‘@CA’ ‘/’ ‘

C

R

L

F

’

rr,rr,…,rr: Shows the route information in 2 hexadecimal digits and ASCII characters Value: 00h to FEh, number

of relay stations maximum 10 units



With Format 1, the route information is entered directly in the command.



With Format 2, transmission is based on route information set in the route register with the RT command or on
the content of the Destination ID. When entering the route information, enter the Equipment ID of the target unit
at the end. If no route information is set (NA set for the RT command), the equipment set as the Destination ID
will be the target station.



It is possible to make the source station the target. In this case, after entering one or more relay stations, enter
the Equipment ID of the source station at the end.

Example: The RSSI of target equipment number 8F is measured over all channels. The relay stations are 01, 02,
and 03.



Source station status

Test command: @CA / 01,02,03,8F

C

R

L

F

or @CA

C

R

L

F

Test response: *CA = 00

C

R

L

F

Receive response with regard to the data transmitted from the target station:

*DR = 80 7C7D....7E7D

C

R

L

F

A response for 64 channels of RSSI is returned as 128-byte (80 hex) ASCII characters (code is minus)



Target station status

There is no response.

«
...
47
48
49
50
51
...
»

Содержание MU-4-434

























































































Отзывы:

Нет отзывов