CIRCUIT DESIGN MU-4-434 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 88

CIRCUIT DESIGN MU-4-434 Скачать руководство пользователя страница 27

OG_MU-4-434_v10e Circuit Design, Inc.

27

OPERATION GUIDE

1. Data transmit command, data transmit response and data receive

The  data  transmit  commands  are  commands  to  transmit  user  data  from  the  source  station.  The  target  station
outputs  a  data  receive  corresponding  to  the  data  transmit  command  issued.  There  are  three  types  of  transmit
command - data transmit command 1, data transmit command 2 and data transmit command 3.

Example 1 Data transmit command 1 ( For 1:1 and 1:N systems)

It is also possible to receive an ACK response.

Source station side

Source
station

User

controller

*DT=05

@DT 05 ABCDE

①Data transmit command 1

②

Data transmit response

Target station side

User

controller

Target

station

③Send data

④

Data receive 1

*DR=05 ABCDE

Example 2 Data transmit command 2 (Using the relay function, with ACK, route information specified in
the route register)

Source station side

Source
station

User

controller

*DT=05

@DT 05 ABCDE /A

①Data transmit command 2

②

Data transmit response

Relay

station

⑥

ACK response

*DR=00

Target station side

User

controller

Target

station

④

Data receive 2

*DR=05 ABCDE

⑤

ACK return

③Send data

Example 3 Data transmit command 3 (Using the relay function, with ACK, route information entered in
command)

RSSI information is included at the front of the data receive. The RSSI level of the signal received at the target
station is included at the front of the ACK response.

Source station side

Source
Station

EI=01

User

controller

*DT=05

@DT 05 ABCDE %A 02,03

①

Data transmit command

3

②

Data transmit response

Relay

Station

EI=02

⑥

ACK response

*DC=45 00

Target station side

User

controller

Target

Station

EI=03

④

Data receive 3

*DC=45 05 ABCDE

⑤

ACK return

③Send data

«
...
25
26
27
28
29
...
»

Содержание MU-4-434

























































































Отзывы:

Нет отзывов