CIMLINE M Series Скачать руководство пользователя страница 4

Страница: 4 / 76

OPERATOR MUST READ AND UNDERSTAND ENTIRE

OPERATORS MANUAL BEFORE PROCEEDING.

THIS PAGE ONLY PROVIDES AN OVERVIEW OF SAFETY INFORMATION

Required clothing

includes:

Gloves with wristlets • Heavy leather boots or shoes • Face shield

• Long sleeve shirt with sleeves rolled down and cuffs buttoned

• Long pants with no cuffs

GENERAL OPERATION SAFETY:



Perform a DOT pre-trip inspection before towing.

• Always use pin with swivel jack.



Never go under trailer with out first stabilizing trailer.

• Never use a damaged swivel jack.



Never touch material expelled by melter while still hot. • Never stand on any part of the machine.



Do not operate without safety cover on hose.

• Load melter from ground level.



Never leave machine unattended while it is running.

• Do not touch exhaust stacks or mufflers.



Keep material door closed at all times except when adding material.

Personal Safety

The melter operates at elevated temperature which can cause

burns.

Operator and anyone working in close proximity to hot

materials must always wear protective clothing.

WARNING

Signal Words in Manual:

The signal words

DANGER, WARNING

and

CAUTION

, are used to identify levels of

hazard

seriousness.

NOTICE:

Is used to address practices not related to personal

injury.

NOTICE

DANGER!

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

DANGER

WARNING!

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

WARNING

CAUTION!

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

CAUTION

Содержание M Series













































































Результаты поиска

Содержание M Series

Отзывы:

Похожие инструкции для M Series

Бренды по названию

Популярные бренды

CIMLINE M Series, Руководство владельца и оператора

Результаты поиска

Содержание M Series

Отзывы:

Похожие инструкции для M Series

Бренды по названию

Популярные бренды