ciil UltraView CL-2667, Руководство пользователя

Страница: 6 / 56

25. Do NOT install the product at such unstable locations as moving objects, constantly vibrating props, or
uneven surfaces. Improper installation may cause products to fall off. Follow mounting instructions
properly for safe operation of the product.
26. Do NOT install the product near any poisonous gas or chemically unstable atmosphere as it may
cause fire.
27. Do NOT install the product near any strong magnetic or electrical current field. It may cause fire,
electric shock, or severe damages to the product. The product may be subject to any electromagnetic
radiation, causing deterioration of content picture quality.
28. Do NOT leave any fire source such as candles close to or on the product as it may be a cause for fire
or damages to the product.
39. Do NOT move or transport the product with any cables (power cables, content connectivity cables)
plugged in to the source devices. Damages may occur to the cables, plugs, or jointing connectors
of the cables due to forcible bending and stress, which may cause damages to the waterproof seal
of the product, making it subject to fire, electric shock, or shorted circuit.
30. When unplugging, always grab the plugs of power cords or cables. Improper pulling of the cords or
cables may cause damages to the waterproof seal of the product, making it subject to fire, electric
shock, or shorted circuit.
31. Do NOT climb on the product.
32. Two persons or more shall transport the product.
33. Do NOT use any other power cords or connection cables than what is provided with the product
or from the manufacturer directly. Use of untested, unauthorized, or substituted power cords or
connection cables may be a cause for malfunction, fire, electric shock, or severe damages to the
product. Also such use of improper or undesignated power cords or connection cables will void
product warranty.
34. Always leave the Power Off when plugging or unplugging the power cords or connection cables
to avoid electric shock or damages to the product.
35. Do NOT use any chemical such as paint thinner or benzene to clean the product’s exterior. It may
cause scratches on the surface, erasing proper indications, identification labels, or instructions on
the exterior, which may be a cause for misuse and improper operation of the product.
NOTE TO THE DISPLAY SYSTEM INSTALLER:
This reminder is provided to call attention to Article 820-44 of the National Electric Code that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the facility, as reasonably close to the point of cable
entry as possible
This LED display operates on 120 volts 60 Hz, AC current. Insert the power cord into a 120 volts 60
Hz outlet. The main plug is used as the disconnect device and shall remain readily operable.
To prevent electric shock from the display, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
Never connect the LED display to 50 Hz, direct current, or anything other than the specified voltage.
CAUTION:
Never remove the back cover of the LED display as this can expose you to very
high voltages and other hazards If the display does not operate properly, unplug the LED
display and call your authorized dealer or service center
English-3 English-2
English
the cabinet� This could cause the product to tip over and cause
damage and/or personal injury�
16� If monitor or glass is broken, do not come in contact with the liquid
crystal and handle with care�
17� Follow instructions for wall, shelf or ceiling mounting as
recommended by the manufacturer�
18� An outdoor antenna should not be located near overhead power
lines or any electrical circuits�
19� If an outside antenna is connected to the receiver, confirm that the
antenna system is grounded to protect against voltage surges and
built up static charges� Section 810 of the National Electric Code,
ANSI/NFPA No� 70-1984, provides information with respect to
proper grounding for the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection
to grounding electrodes and requirements for the grounding
electrode�
NOTE: To the display system installer: This reminder is provided
to call attention to Article 820-44 of the National Electric Code that
provides guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding system of
the facility, as reasonably close to the point of cable entry as possible
Power source
This LCD display operates on 120 volts 60 Hz, AC current� Insert the
power cord into a 120 volts 60 Hz outlet� The mains plug is used as
the disconnect device and shall remain readily operable�
To prevent electric shock from the display, do not use with an
extension cord, receptacle, or other outlet unless the blades and
ground terminal can be fully inserted to prevent blade exposure�
Never connect the LCD display to 50 Hz, direct current, or anything
other than the specified voltage.
CAUTION: Never remove the back cover of the LCD display as this
can expose you to very high voltages and other hazards� If the display
does not operate properly, unplug the LCD display and call your
authorized dealer or service center�
Adjust only those controls that are covered in the instructions, as
improper changes or modifications not expressly approved by NEC
could void the user’s warranty�
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
POWER SOURCE
GENERAL SAFETY PRECAUTIONS CONTINUED
6
7