manualshive.com logo in svg

CIAT 1-PH HEE BOX, Руководство по управлению

Поделиться
Скачать
CIAT 1-PH HEE BOX Скачать руководство пользователя страница 21

0 %

100 %

P 130

Valve ctrl

Heating operation

Hot Proportional Band

P152 or P153

Setpoint

Room T°

5.2.2.3 Cooling coil, COOLING mode

"Stop" position: the valve is closed

"COMFORT" position: the opening of the valve will depend on the difference between the regulated temperature value (room) 

and the setpoint. Regulation will only start after a 30-second time delay on the fan operation feedback contact. An integral action 

must be entered into the parameters.

0 %

100 %

P 135

Valve ctrl

Cooling operation

Cold Proportional Band

P150 or P151

Cooling setpoint

Room T°

5.3 TPL regulation: 

TPLs are destratifiers which can only be regulated according to the fan speed.

This is calculated from the difference between the room temperature measured by the sensor in the Master 1-ph HEE BOX (or 

remotely if this option has been chosen) and the sensor fitted in the TPLs.

 

 EN-21  

1-PH HEE BOX

Содержание 1-PH HEE BOX





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды