background image

 

MetCam Technical Manual

 

Document P/N A1604870010 

13 

 

 

4.4

Power Up 

When power is applied to MetCam, the Power LED will start blinking Green. This is an indication that the power has been 
connected properly and is within the allowed range. If the LED does not turn blinking Green there is a problem with the 
power connection. 

Wait approximately 60 seconds for MetCam to complete its boot procedure 

 

The LED will change from blinking green to a constant green.  

 

The 4-20 mA output provides 2.4 mA (Warmup state) 

 

The 4-20 mA output changes to 4 mA after warmup is completed (typically 30 minutes) 

The following figure shows the location of the Indicator LED (the green arrow is pointing to it) 

 

 

4.5

4-20 mA Signaling and LED Status 

MetCam uses a stepped output and needs to be installed as a 4 wire transmitter.  
The signaling range is 3.8 to 20.5 mA. The signaling includes the following discrete level signals: 

 

Normal - 4 mA 

 

Alarm (A1) 

– 16 mA 

 

Alarm (A2) 

– 20 mA 

There is no alarm latching in MetCam. 
The 4-20 mA outputs 0 mA when there is no power or a broken 4-20 mA line. 
The MetCam LED is indicative of the health status of the unit. 

The 4 LED cases are: 

LED Color 

On 

Blinking 

Green LED 

"PWR" 

"BOOT" 

Red LED 

"ERR" 

"CHK" 

Legend: 

Indication 

Meaning 

PWR 

MetCam is powered and functioning normally 

BOOT 

MetCam is booting, during boot the unit is non-functional 

ERR 

MetCam is in fault 

CHK 

MetCam has a fault that originates in the installation, check the external conditions 

Содержание MetCam A160100 0 Series

















Отзывы: